Cat Emcp 2 Manual
Cat Emcp 2 Manual
The logs include: EMCP 3.1, 3.2, AND 3.3 GENSET CONTROL Events for the EMCP 3 GSC ENGINE CONTROL Events for a J1939-compatible engine ECM DIGITAL AVR Events for the Caterpillar Digital Voltage Regulator (CDVR) EMCP 3.2 AND 3.3 ONLY EXTERNAL I/O Events for an Auxiliary Input/Output module (DIO) EMCP 3.3 ONLY THERMOCOUPLE Events for the. CAT EMCP 3.2 & 3.3 Installation Guide 1. Unpack the monitor, antenna and the data/power cable. The 25 pin connector plugs onto the front of the OmniMetrix® monitor. This cable includes wires to power the monitor as well as wires for alarm inputs, relay outputs and analog inputs. Take a moment to inspect all components to verify.
Usage:
Options can be retrofitted to the EMCP II+. The following optional items are available for purchase at the parts department. The items must be wired per the service manual SENR5832, Electronic Modular Control Panel II+ (EMCP II+) For MUI Engines. To complete the installation, it is the responsibility of the installer (dealer service personnel) to provide the miscellaneous terminals, wires, tie wraps and hardware. If there are any questions concerning the application of any options, refer to the service manual SENR5832, Electronic Modular Control Panel II+ (EMCP II+) For MUI Engines.
NFPA 99 Alarm Module
To determine the proper jumper configuration, refer to the service manual SENR5832, Electronic Modular Control Panel II+ (EMCP II+) For MUI Engines.
One 130-3349 Control Group
One 9Y-0947 Annunciator Film
NFPA 110 Alarm Module
To determine the proper jumper configuration, refer to the service manual SENR5832, Electronic Modular Control Panel II+ (EMCP II+) For MUI Engines.
One 130-3349 Control Group
One 7C-9130 Film
One 8C-4646 Jumper Strap
Prime Power Alarm Module
To determine the proper jumper configuration, refer to the service manual SENR5832, Electronic Modular Control Panel II+ (EMCP II+) For MUI Engines.
One 130-3349 Control Group
One 9Y-9776 Film
Custom Alarm Module With Horn
One 130-3332 Control Group
One 130-3326 Film
One 130-3327 Film
Custom Alarm Module Without Horn
One 130-3324 Control Group
One 130-3326 Film
One 130-3328 Film
2301A Governor Controller (4P-2788)
One 4W-5971 Potentiometer
One 4W-5972 Knob
One 4W-8790 Fuse Block
One 7C-4550 Seal - Rotating Shaft
One 7E-7845 Film - DC Fuse
One 7T-0037 Fuse
One 131-5453 Governor Control Assembly
Governor Raise/Lower Switch
One 7N-8008 Switch
524/1724 Governor Controller (7E-1232)
One 3K-3782 Fuse
One 4W-5972 Knob
One 4W-8790 Fuse Block
One 7C-4550 Seal - Rotating Shaft
One 7E-1246 Potentiometer
One 9Y-9782 Film - Identification
One 131-5455 Control Assembly
Starting Aid Switch
9D-3721 Switch, Manual SAS (2 position)
Overvoltage Relay
123-4944 Relay, 208 Volt
123-4945 Relay, 240 Volt
123-4946 Relay, 416 Volt
123-4947 Relay, 480 Volt
126-0558 Relay, 600 Volt
Overcurrent Relay
112-7959 Relay, 3 Phase Overcurrent Relay
Reverse Power Relay
5N-5510 Reverse Power Relay, 0-480 Volt
7C-4378 Reverse Power Relay, 600 Volt
Synchronizing Light Module
106-5171 Synchronizing Module Group, 0-480 Volt
106-5169 Synchronizing Module Group, 600 Volt
Dustproof Kit (121-4705)
Three 5L-5180 Washer - Sealing
Two 5L-5840 Washer - Sealing
Two 7C-2954 Gasket - Module
Two 7C-4550 Seal - Rot Sft
One 7C-4910 Seal - Washer
One 103-6272 Seal - Control
Auxiliary Or Engine Failure Relay
128-3326 Relay Group; 3PDT Relay, Socket, Spring
Remote Annunciators
These items are intended for remote mounting.
7E-8270 Instrument Panel Group, 2 Light NFPA 110
7C-5296 Instrument Panel Group, 8 Light NFPA 99 (Small Box)
131-1960 Instrument Panel Group, 8 Light CAM
131-1961 Instrument Panel Group, 16 Light CAM
131-1962 Instrument Panel Group, 8 Light NFPA 99 (Large Box)
Caterpillar Emcp 2 Manual
131-1963 Instrument Panel Group, 16 Light NFPA 99
144-8325 Instrument Panel Group, 8 Light EMCP RAN
131-1965 Instrument Panel Group, 16 Light NFPA 110 (EMCP RAN & CAM)
Customer Interface Module (CIM)
This item is intended for remote mounting.
9Y-6496 Control Group
Customer Communication Module (CCM)
This item is intended for remote mounting.
117-6170 Control Group
| Latest news: |
Thread Rating:
- 1 Votes - 5 Average
Caterpillar EMCP 2+ Wiring Diagram |
Emcp Ii
Post: #1 |
| Caterpillar EMCP 2+ Wiring Diagram I will share any wiring diagram of Caterpillar EMCP 2+, this file use for troubleshooting and testing adjusting. Please hit THANKS if this useful for your job. trob73maker, proud to be a member of GarageForum since Mar 2019. |
|
« Next Oldest Next Newest » |
User(s) browsing this thread: 1 Guest(s)
Cat Emcp 2 Manual